Відео

great content! thank you and congrats! really! quick question, do you have one or two books/titles to indicate, which you were based on to make this video?

Great 👍

Great video, very a simple and straightforward. I studied industrial engineering and wanted a small refresher on the tools available for a project.

Very useful, thank you

What do you mean with the process not being centered?

That's great

Hi Andy, i have seen a scenario where If PP and PPK fail to achieve the minimum requirement e.g. 1.67 but CP and CPK passes. The big factor is the tolerance is so small it doesn't leave much room for any process variation as PP and PPK is long term. What are your thoughts on this due to tight tolerances?

Hello Andy, Thanks for the video. I wanna know one thing if we take multiple samples and run them for specific hours what will be the operation cycle in that case in the MTTF formula or failure rate formula. will it be the (duration for which we run those samples) or (samples multiplied by duration for which we run the samples)

What a great lecture!, This has summarized my QA tools lecture which was taught in 5 different lectures, Awesome tuts.

The video is not displaying but I can hear the sound. Do you have other source where you have this video? It would be really helpful

Amazing explanation! thank you so much <3

Hey Andy! Have my exam tomorrow, the cheat sheet I can use as long as it’s whole punched in the folder right?

Very nice information. Thanks Sir.

Hi Andy, on your discussion for u-chart, your UCL/LCL has n-bar but in other books I see its n(i), not n-bar. Could you clarify?

Thanks a lot. I am so grateful to you

Really like your videos Andy. A good blend of theory and practice and always clearly communicated. Thank you.

Loved the coverage of important aspects and how and at what place they are used in the industry processes. Thanks Andy!

A very good into video, a great follow-up video would be a deeper dive into each tool.

great

How do you know to default to general inspection level II and not I or III?

What a simple way of explaining all these QC tools!!

Thank-you so much brother for your advice

This video was REALLY helpful and detailed, thanks

GREAT

Hello Andy, please let me ask a very elementry question. If we want to increase Cpk value we should increase the numerator of that fraction. Since the specification limits are directly influenced by customer how to increase it? Thanks.

This was an EXCELLENT summary to watch before my Quality Management exam! Thank you so much🙌

Super nice explanation with a practical example thank you! I only miss one minor point the stated Phase of PDCA or DMAIC per Quality Tool. You only say it specifically at 1. Flow Chart. Maybe someone could typ them as a reaction.

Great explanation!!Thanks

Thank you Very much❤

Walter A shewhart was the founder of the PDCA cycle, and Deming made it popular by naming it the PDSA cycle.

Is there a global certification for FMEA?

Great video! Thank you!

Your the best teacher ❤❤❤

Hi Sir, In order to qualify under the education credntial waiver, Do we require to possess education in quality related program? I have a master's degree in Industrial engineering from an US university. But its not a Quality engineering perse. Please clarify?

If our LSL is - what will do

Process capabilities are not always normally distributed. Could be but NOT. WHY? It’s a part of production and operation management with an ultimate goal to finish the processing MOST efficiently with ZERO defect. A whole lot sub functions are in question and MUST work smoothly to end a process. Could be a ONE time process or a PERPETUAL process. BE careful of its SIDE effects related to fatigue and boredom.

Excellent video!

I have struggled with this concept for a while, and now get the basics to move forward again. Thank you!

All I can say is excellent content and presentation.

That was seriously very helpful.

Excellent learning!! with the help of your videos, thank you, & God bless you!!

Thanks

Excellent !! great , Thank you!! do you have all the formulas sheet for calculating control charts values

Don’t you think that Methods includes Management and Machines Maintenance?

Helpful. In kenya, we say, "Asante kwa kazi nzuri."

Amazing content thanks!

Excellent❤❤❤, One question What if we have different tolerance for each subgroup, For example for subgroup 1 we have +/-2 and for subgroup 2, +/-3 and so on, Have we calculate process capability in this condition?❤❤❤❤❤❤

Great video, nice and straight to the point. Thank you 😃

why did u added 14x1000